An experimental investigation into non-linear wave loading on horizontal axis tidal turbines

Tidal turbines are subject to large hydrodynamic loads from combinations of currents and waves, which contribute significantly to fatigue, extreme loading and power flow requirements. Physical model testing enables these loads and power fluctuations to be assessed and understood in a controlled and repeatable environment. In this work, a 1:15 scale tidal turbine model is utilised to further the fundamental understanding of the influence of waves on tidal turbines. A wide range of regular waves are generated in both following-current and opposing-current conditions. Wave frequencies range from 0.31 Hz to 0.55 Hz & wave heights from 0.025 m to 0.37 m in a fixed 0.81 m/s current velocity. Waves are selected and programmed specifically to facilitate frequency domain analysis, and techniques are employed to isolate the effect of non-linear waves on turbine power and thrust.Results demonstrate that wave action induces large variations in turbine power and thrust compared to current only conditions. For the range of conditions tested, peak values of thrust and power exceed current-only values by between 7%–65% and 13%–160% respectively. These wave-induced fluctuations are shown to increase with wave amplitude and decrease with wave frequency. Following wave conditions exhibit greater variations than opposing for waves with the same wave height and frequency due to the lower associated wavenumbers.A model is developed and presented to aid the understanding of the high-order harmonic response of the turbine to waves, which is further demonstrated using steady state coefficients under assumptions of pseudo-stationarity. This approach is proven to be effective at estimating wave-induced power and thrust fluctuations for the combinations of waves, currents and turbine state tested. The outcome of which shows promise as a rapid design tool that can evaluate the effect of site-specific wave–current conditions on turbine performance.     

Fabrication of Pre-tilted Vertical Alignment Layers for High-Speed Liquid Crystal Display Using Bi-functional Photoreactive Monomers

Abstract

To enable recent 3D and moving picture applications, liquid crystal displays (LCD) must exhibit fast response and wide viewing angle characteristics. Pre-tilted vertical alignment layers for high-speed LCD were fabricated using bi-functional photoreactive monomers. The monomers can be confined to the polyimide layer and photo-polymerized by UV exposure under voltage. Response characteristics of photo-controlled alignment films according to the structure were investigated. Vertical alignment properties were evaluated using a polarizing optical microscope, and electro-optical characteristics were compared through the voltage-transmittance curve and response time measurement. Faster response speed could be obtained by using photoreactive monomers having a long alkyl chain.     

Liquid crystalline properties of 4‐hexyloxybenzylidene‐4′‐alkyloxyanilines

The liquid‐crystalline polymorphism of the homologous series of 4‐hexyloxybenzylidene‐4′‐alkyloxyanilines is investigated. Basing on the polarization microscopy (POM, TOA), the DSC calorimetry and miscibility studies the following mesophases were detected: nematic, smectic A, smectic C and smectic I. The phase diagrams of the compounds of these series with 4‐hexyloxybenylidene‐4′‐pentylaniline (as the standard of mesophases) show induction of the smectic F mesophases. Their dependence on the alkyl chain length and mole fraction is shown.     

Fast switching of vertically aligned negative liquid crystals by optically hidden relaxation

We propose a method for fast switching of vertically aligned (VA) negative liquid crystals (LCs) by hiding the relaxation process of LCs. During the turn-off process, a strong in-plane electric field is applied for a short duration of time instead of relying solely on the slow relaxation of LCs. The LC molecules are rotated to the transmission axis of one of the polarisers by the applied in-plane electric field, resulting in turn-off switching that is 5.8 times faster than that of a conventional VA cell. By applying an overdriving scheme, we experimentally obtained a total response time of 3.3 ms.     

Fabrication of photoluminescent liquid crystal device using an in situ self-assembled molecular layer of a pyrene derivative

An in situ self-assembled molecular layer of 1-pyrenesulfonic acid sodium salt as an alignment agent was formed on indium tin oxide substrates for vertically aligning liquid crystals (LCs). The thus-aligned LCs exhibited uniform vertical alignment under crossed polarisers. The electro-optical characteristic of the LC cell fabricated using this method exhibited better performance than those of conventional LC cells with a polyimide alignment layer. Because the proposed alignment method is a simple one and involves low concentrations of the alignment agent (0.05 wt%), it is highly cost-effective. Further, the pyrene derivative, when mixed with LCs, exhibited photoluminescence (PL) under ultraviolet light. Given that the proposed method resulted in highly vertically aligned LCs and the alignment agent exhibited PL, the method should find wide use in the fabrication of colour-filter-free LC displays.     

On the application of a single‐crystal κ‐diffractometer and a CCD area detector for studies of thin films

A multipurpose six‐axis κ‐diffractometer, together with the brilliance of the ESRF light source and a CCD area detector, has been explored for studying epitaxial relations and crystallinity in thin film systems. The geometrical flexibility of the six‐axis goniometer allows measurement of a large volume in reciprocal space, providing an in‐depth understanding of sample crystal relationships. By a set of examples of LaAlO₃ thin films deposited by the atomic layer deposition technique, the possibilities of the set‐up are presented. A fast panoramic scan provides determination of the crystal orientation matrices, prior to more thorough inspection of single Bragg nodes. Such information, in addition to a broadening analysis of families of single reflections, is shown to correlate well with the crystallinity, crystallite size, strain and epitaxial relationships in the thin films. The proposed set‐up offers fast and easy sample mounting and alignment, along with crucial information on key features of the thin film structures.     

Evolution of downsized crescent-shaped dune in wind tunnel experiment

The migration of a downsized crescent-shaped dune was investigated in a wind tunnel experiment.Quantified upwind influx and vertical oscillation of the sand bed were introduced to modulate the saturation level of the sand flux above the dune surface to affect dune evolution.The evolution was recorded by top-view photography and then abstracted as the evolution of self-defined characteristic quantities using a digital image processing algorithm.The results showed that,in contrast to the case for spanwise quantities,the evolution of streamwise quantities corresponds to a linear increase in the modulation magnitude more positively and in a monotonic and convergent manner.In contrast with quantities on the windward face,the changes in quantities with respect to the horns were nonmonotonic with time and almost uncorrelated with the variation in modulation strength,which reveals the distinctiveness of leeside evolution.     

Material profile influences in bulk‐heterojunctions

The morphology in mixed bulk‐heterojunction films are compared using three different quantitative measurement techniques. We compare the vertical composition changes using high‐angle annular dark‐field scanning transmission electron microscopy with electron tomography and neutron and x‐ray reflectometry. The three measurement techniques yield qualitatively comparable vertical concentration measurements. The presence of a metal cathode during thermal annealing is observed to alter the fullerene concentration throughout the thickness of the film for all measurements. However, the absolute vertical concentration of fullerene is quantitatively different for the three measurements. The origin of the quantitative measurement differences is discussed. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 1291–1300     

Curvilinear smoothed particle hydrodynamics

We suggest a new set of equations to employ smoothed particle hydrodynamics (SPH) in a curvilinear space, and we refer to it as curvSPH. In classical SPH, the horizontal and vertical resolution of discretization is supposed to be equal for fluid particles. However, curvSPH makes the horizontal and vertical resolutions independent from each other. This is performed by transformation of physical space into an appropriate computational space with a different scale in horizontal and vertical directions. Solving a problem using SPH in a curvilinear space also provides capability to model curved boundaries as straight lines. In classical SPH, special care is needed to reach a uniform mass distribution along curved boundaries; however, producing uniform mass distribution along a line using curvSPH is straight forward. Different simulations, including simulation of a flip bucket are performed to demonstrate the applicability of the proposed method. Good agreement of results with experimental data and classical SPH confirms the capabilities of curvSPH. Copyright © 2016 John Wiley & Sons, Ltd.